■Design Regular color punching leather riders that fit seamlessly on a variety of bikes and scenes. The universal single rider design does not limit the type of car or occasion in which it is worn. ``I want to wear a leather jacket even in the summer.'' We aimed to create an item that would fulfill that request.

■Product features・With pockets for attaching shoulder, elbow, and spine pads・Equipped with Velcro tape for chest protector

■Material front: Punching cow (2mm diameter) Back: Polyester mesh (COOLDEHYBER)

Vietnam

*Unit is cm (centimeter)
*The listed sizes are finished dimensions, and there may be slight differences depending on the product.

How to choose size

* Due to the riding pattern, the sleeves may feel long.
*If the material is leather, the sleeve length will be shortened by 1-2 cm.
* If you are concerned about the length of the sleeves, it is possible to shorten the sleeves for an additional fee.

All KADOYA products are written in Japanese size.
In the table below, please check the Japanese size and overseas size (US, EU, UK).
(The sense of size varies depending on the manufacturer, so please check it as a reference.)

Men's size

Ladies size

*Please use the waist measurement as a reference for pants.
*The listed sizes are for reference only and may differ from the actual sizes.

Punching cow

The punching cow is a leather with a 2mm -diameter ventilation hole in a glossy cowhide of 1.3 to 1.5 mm thick. The interval between holes is 5mm, and these are the best balance derived by our long -standing development and experience.

The larger the ventilation hole, the cooler it will be, but if you fall, you have to think about splitting from the hole. The answer that arrived there was a 2mm diameter hole and a 5mm pitch. These are the numbers required to maintain the strength of leather.

In addition, the surface is embossed. This not only creates facial expressions in leather, but also plays a role in giving leather hardness, and punching cow has the best strength by opening holes in hard leather.

Just like with our skin, regular maintenance is important to prevent damage and keep leather products in good condition. Here we will introduce some self-maintenance methods to ensure you can enjoy your leather products for a long time.

(When using maintenance products such as cleaners or oils, always test on an inconspicuous area to make sure they do not cause stains or discoloration.)

Step 1

Use a horsehair brush to remove dirt and dust from the surface of the leather. Be sure to brush the seams as well. If the leather is very dirty, wipe it with a tightly wrung out wet towel.

Step 2

Take Ref / LEATHER CLEANER through the cloth until your fingers are slightly damp. When the cleaner has dried, soak the cloth with an appropriate amount again.

Step 3

Wipe the entire leather in several steps. This process will bring it closer to bare skin. Dirt and color will transfer to the cloth, but this is proof that the old oil and dirt have been removed.

Step 4

The finish can be either matte, natural or glossy depending on the oil characteristics, so please choose the oil according to your preference.

Step 5

Apply your chosen oil to the clean side of the cloth, using only small amounts of oil at a time.

Step 6

Apply the oil thinly, spreading it evenly over the entire leather. If there is not enough oil, add a little at a time.

Step 7

Brush the entire leather surface with a horsehair brush to allow the oil to soak in. For larger areas, it is more effective to use a larger brush. We recommend using a separate brush for dust removal.

Step 8

From here on, we will introduce a "step" that we recommend for those who want to pay more attention to the finish. Wipe the entire glove with the mouton side. Wiping it dry will remove any excess oil remaining on the surface and prevent stickiness.

We offer a specialized leather cleaning service called ``Refleather''.

What is Refresher?

The new common sense is to wash leather products before wearing them.

The traditional method of cleaning leather products in Japan has been dry cleaning using chlorinated solvents.

While this removes dirt, there are also cases in which the color fades and the oil content from the leather is removed, and using a fatliquoring agent to replace the lost fat content can result in an unnatural or unpleasant stickiness. There was a problem.

Ref Leather uses a special soap specifically for leather, and can be washed with water as well as dry. The important thing here is to remove dirt and replenish nutrients, including lost fat. This will restore suppleness and elasticity, allowing you to once again appreciate the gentleness and strength that leather originally possessed.

You can wash all kinds of leather products (genuine leather), including leather jackets, leather overalls, pants, coats, skirts, and boots. It is also possible to clean colored models that were avoided with conventional cleaning.

Click here for details

From simple and basic high-quality standards to avant-garde items based on the highest specs and philosophy. A rider wear brand that goes well with town use as well as commitment to safety and functionality.